Skip to content
This product has been discontinued.
DART 6 in. Actuator Kit - am-3076a - migrated

DART 6 in. Actuator Kit

by AndyMark
$304.00 - $304.00
$304.00
$304.00
$304.00 - $304.00
$304.00

The information provided on this page is retained for posterity.

This product is no longer for sale at AndyMark and has been discontinued , check here for remaining components

This product is currently unavailable for purchase

SKU am-3076a
  • Description
  • Specifications
  • Documentation

  • DART is a strong, fast, linear actuator designed by the engineers at iR3 Creative. It's driven by a CIM Motor and uses a 0.2 inch pitch ACME lead screw to actuate an aluminum tube 6 inches. Two different sensor feedback methods are available with this actuator, with a potentiometer included in the assembly. An optional DART Sensor Pack is available (but not included), using hall effect sensors detecting a moving magnet near the lead screw nut. iR3 Creative developed this actuator in 2014, and it has received a design upgrade for a new release in January of 2016. This design upgrade focused on cost savings compared to the previous design, and therefore the price has been dropped by over $80. This version functions the same as the previous version, but the internal parts are unique and different from the past version. This is why we have re-numbered this version to have an "a" as the suffix of the part number, am-3072a. The steel, double leaded screw has a 0.50 in. O.D., a 0.20 in. lead, and 53% efficiency. The 6 in. stroke assembly weighs approximately 3.0 lbs without the CIM motor and 5.8 lbs with. There is a 12 in. version ( am-3072a) of this same DART actuator if you wish to have a longer stroke.

    Linear actuators are not meant to be side loaded. The use of rod ends is encouraged to avoid these type of loads. This product is shipped unassembled. Please see the assembly instructions for how to put this product together. We chose to ship this product unassembled in order to be able to offer it at a low price.

    Note: The CIM Motor (am-0255) and the DART Sensor Kit (am-3077a) are NOT included in this product, and need to be purchased separately.

    Improvements, as of November, 2016:
    We've listened to customer feedback and responded with these improvements.

    • Rod Cap is now zinc-plated steel instead of aluminum.
    • The 5/16-24 female mounting hole at the end of the actuator is much stronger.
    • 3/16 in. Shoulder Screw holding on the 14T gear on the linear drive has much longer threads.
    • AndyMark is assembling the entire linear module (this is why we raised the price by $14)



    Screw Specifications:
    Standard Ratio:

    • 2.5:1 200lbf at 5.33 in/s
    Optional Other Ratios:
    • 2:1 160 lbf at 6.67in/s
    • 1:1 80 lbf at 13.3 in/s
    Sensing Features:
    • 10-turn potentiometer is included, sensing the turns of the leadscrew
    • A 14 tooth gear on the lead screw turns a 96 tooth gear on the potentiometer for a 6.85:1 ratio
    • The potentiometer will turn 4.4 times during a 6 inch travel
    • An optional hall effect sensor kit (am-3077a) is available (but not included) as an add on

    APPLICATION NOTE:
    Linear actuators are not meant to be side loaded. The use of rod ends is encouraged to avoid these type of loads. Each end is tapped for a 5/16 in.-24 thread to accept common rod end sizes.

    The DART was designed to achieve equivalent forces of a 2 in. bore pneumatic cylinder at 60 psi and to be used with a CIM motor fused at 40 amps. While it's possible to exceed these values you may see decreased life in the various ware components.

    It is recommended to run this actuator with hall effect and/or current protection as it is possible to stall or "stick" the lead screws when stalled against a hard stop at both ends of travel. It's recommended to use the the hall effect switches to limit travel of the actuator from the end stops. When using faster ratios it may be possible to overrun the limits slightly and programming methods may require ease into stroke ends. If you are not able to program these functions we recommend using a Talon SRX which has on-board switch monitoring and current protection.
    • Efficiency: 53%
    • Weight: 5.8 lbs. (with CIM)

  • CAD Files

    am-3076a DART_6.STEP

    Layout Prints

    am-3076a DART_6.pdf

Customer Reviews

Based on 5 reviews
60%
(3)
20%
(1)
20%
(1)
0%
(0)
0%
(0)
j
jt from Alamo
Review

5 Stars

S
SS from Calmar
Review

3 Stars

P
PY from West Lafayette
Strong Actuator

This is a strong fast actuator that is a little challenging to put together

J
JT from Menasha
DART, 6' Actuator Kit (am-3076a)

The DART actuator shipped on time, and is a quality product. Exactly what we needed for this year's challenge.

C
CS from Oxon Hill
Review

5 Stars

Purchase options
Select a purchase option to pre order this product
Countdown header
Countdown message


DAYS
:
HRS
:
MINS
:
SECS