Skip to content
AndyMark will be closed on Fridays through August 1st to allow staff flexible summer work hours.
AndyMark will be closed on Fridays through August 1st to allow staff flexible summer work hours.
8 in. Pneumatic Wheel Kit - am-0970 - migrated

8 in. Pneumatic Wheel Kit

by AndyMark
Save 33% Save 33%
$40.00
$40.00 - $40.00
$40.00
$27.00
$27.00 - $27.00
$27.00
The 8 in. Pneumatic Wheel Kit is a high-traction wheel which includes a grippy rubber tire, an pneumatic inner tube, and a strong plastic hub.
SKU am-0970
  • Description
  • Specifications
  • Documentation
  • Here is a high-traction wheel which includes a grippy rubber tire, an pneumatic inner tube, and a strong plastic hub. These parts are shipped to you in kit form. The unique aspect about this product is the competition-ready hub. The hub accepts any 200x50mm tire and inner tube, 1.125 in. (outside diameter) ball bearings (2 per wheel are needed), and the mounting holes needed to install hardware to be sprocket-driven or hub-driven. This wheel ships as a separate tire, inner tube, and hub halves. Assembly is required.

    Important Notes:


    • Diameter: The nominal diameter for this wheel is actually 7.65 in. when inflated normally.
    • Tube pinching: When assembling the tube within the two hub halves, be careful not to pinch the tube rubber between the plastic hub halves. If assembled with the tube pinched between the hub halves, the tube may puncture and leak.

    RPM Rating and notes:


    These wheels are designed to be propulsion wheels for driving a robot or wheel chair. The design intent is to be contacting the ground, being driven by a gearbox at a maximum speed of approximately 500 rpm (which results in 17 feet/sec).

    Within some applications, this wheel has been used as a shooter of objects, spinning at a very high rpm. For these applications, a higher rpm shows that the wheel may wobble, since the valve stem is mounted off to one side of the center of the wheel hub. We have seen properly balanced wheels, using securely mounted hardware (longer screws, washers) that can handle 5,000 rpm. When spinning this wheel at speeds up to 5,000 rpm, please take proper safety precautions.

    Included Items:

    NOT Included Hardware:

    • Bearings
    • #10 Screws and Nuts Needed to Mount a Hub (2 Inch Long Screws are Needed) or a Sprocket (2.25 Inch Long Screws are Needed)
    • Aluminum Hub, if Driven by a Shaft
    ----------------------------------------------------------------------------------------------------

    Wheel Structure:

    The hub halves are held together with the #4-40 screws. This wheel can accept #10-32 screws for mounting sprockets or hubs, but these are NOT included since different length screws are needed to mount hubs or sprockets. These #10 screws can be mounted to the included 1.875 inch diameter bolt circle. The hub halves need to be assembled together so that the valve stem clearance holes line up. Locating features are present for easy alignment.

    Usage:
    With Axle and Hub:
    • In order to drive this wheel with a hub, use Hardware Kit 11, which includes #10-32x2 screws (6) and #10-32 nylock nuts (6)
    With Sprocket:
    • In order to drive this wheel with a plate sprocket, use Hardware Kit 12, which includes a 550 Sprocket Spacer, #10-32x2.25 screws (6) and #10-32 nylock nuts (6).
    • Two (2) bearings are needed for this wheel, if being driven by a sprocket. Use bearings with a 1.125 inch outer diameter. No flange is needed on either of the bearings.
    Use as a caster:
    • If you want to let this wheel spin without being driven, you will need to install two (2) bearings with 1.125 inch outer diameter.
    • Weight: 1.13 lbs

  • Guides

    am-0970 8-inch Pneumatic Wheel Assembly Instructions AM-0970.pdf

Customer Reviews

Based on 52 reviews
63%
(33)
21%
(11)
15%
(8)
0%
(0)
0%
(0)
N
NL from Colombo 08
Great Quality. Product as expected. Highly sati...

Great Quality. Product as expected. Highly satisfied.

L
LY from GAMBRILLS
Excellent way to improve traction

Also reduces impact loads to chassis. Running a #4-40 tap through screw-mounting bosses will eliminate assembly concerns. Durable and reliable, but nice to have a spare in the event of a catastrophic decompression.

T
TK from Cambridge
Review

4 Stars

S
SM from Pittsburgh
Review

5 Stars

D
DV from Bloomington
Review

5 Stars

123
Purchase options
Select a purchase option to pre order this product
Countdown header
Countdown message


DAYS
:
HRS
:
MINS
:
SECS